三端保險絲 30A62V 5.4×3.2 5串
1.適用范圍Scope
本規范適用于蘇州鼎時電子有限公司生產的自控制保護器。
This Specification applies to the fuse linked with heater which made by LANSON ELECTRONICS Corporation.
2.適用安全標準Applicable Safety Standards
UL248-1，Ul248-14。
3.UL認證 UL File Number
E221465.
4.外形與回路圖 Dimensions and Circuit Chart
4.1外形圖 Dimensions
（4）產品的尺寸代碼，J表示4.0mm×3.0mm×0.85mm，H表示5.4mm×3.2mm×1.35mm，K表示9.5mm×5.0mm×2.0mm等。
Dimension code of the product, J means 4.0mm × 3.0mm × 0.85mm, H means 5.4mm × 3.2mm × 1.35mm, K means 9.5mm × 5.0mm × 2.0mm, etc.
5.規格 Rating
|
型號 Part number |
額定電流Current Rating |
額定電壓★ Voltage Rating |
最大阻斷電流Max. Breaking capacity |
保險絲電阻Fuse DCR |
適用電芯數Cells in series |
動作電壓范圍Operating Voltage |
|
A |
VDC |
A |
m Ω |
cell |
V |
|
|
SCP30A5H |
30 |
62 |
80 |
0.5-2.5 |
5 |
17.10~23.50 |
★額定電壓是保險絲組件可以安全阻斷的最大電壓值，不是發熱器組件的動作電壓。
★Rated voltage is the maximum voltage that the fuse can block, not the action voltage of the heater assembly.
6.環境性能 Environmental Characteristics
（1）產品中使用的各種材料的鹵素含量如下表所示。
Contents of halogens used in each material for the product are as follows.
|
鹵素 Halogen substance |
含有量 Content |
|
氯（CL） Chlorine（CL） |
≤ 900ppm (0.09%) |
|
溴（Br） Bromine（Br） |
≤ 900ppm (0.09%) |
|
總和（氯(CL)＋溴(Br)） Total concentration of chlorine (CL) + bromine (Br) |
≤ 1500ppm (0.15%) |
（2）本規范中描述的產品符合ROHS指令。BOM表中的合金、焊料、一些電子漿料含有鉛，但都符合ROHS指令的高鉛豁免相關規定。。
The product described in this specification complies with the ROHS Directive. BOM table contains the alloy, solder, some electronic slurry, including lead, but these are exempted from ROHS requirements.
7.性能Characteristics
7.1．測試一般條件 General Conditions of Measurement
除非特別指定，否則按以下環境條件進行測量。
In the absence of additional test environmental standards, the test environmental standards are as follows;
環境溫度：5～35℃；
相對濕度：45～85%RH；
氣壓：86～106KPa。
Ambient temperature: 5 to 35℃.
Relative humidity: 45 to 85%RH.
Air pressure:86 to 106kPa.
如果在判定產生疑義的情況下，按照以下條件進行測定。
If you have any questions about the test results, please follow the following environmental standards.
環境溫度：20±2℃；
相對濕度：60～70%RH；
氣壓：86～106KPa。
Ambient temperature: 20±2℃.
Relative humidity: 60 to 70%RH.
Air pressure: 86 to 106kPa
7.2．電氣的性能 Electrical Characteristics
|
No. |
項目 Items |
測定條件 Conditions |
技術規格 Specifications |
|
1 |
熔斷時間 Clearing time |
產品參照《電壓動作特性測試方法》連線，向測試板（4-1端或者4-3端）施加對應規格的動作電壓 Apply the operating voltage to the heater. For other procedures, refer to《Voltage action characteristic test method》. |
保險絲組件一分鐘內熔斷。 The fuse shall be melt Within 1min.
|
|
產品參照《電流動作特性測試方法》連線，向測試板（1-3端）施加兩倍額定電流。 Energize both ends of the fuse with twice the rated current. For other procedures, refer to《Current action characteristic test method》. |
|||
|
2 |
通電容量 Current carrying capacity |
產品參照《溫升測定方法》連線，向保險絲組件（1-3端）施加額定電流。 Energize the rated current at both ends of the fuse. For other procedures, refer to《Temperature Rise characteristic test method》. |
保險絲組件1小時內沒有熔斷。 No melting within 1 hour |
注：
電氣性能受基板熱容量、零件、圖案寬度等條件的影響。因此，請將產品安裝在客戶實際使用的基板上確認特性。
Electrical Characteristics is influenced by thermal capacity of PCB, parts, pattern width, and so on. Therefore you should check it on your PCB.
7.4．耐久性能 Endurance Characteristics
|
NO |
項目 Items |
測定條件 Conditions |
規格 Specifications |
|
1 |
高溫 Dry heat |
在100±5℃環境保持6小時后，常溫常濕條件下放置1小時后進行測量。 The fuse shall be stored at a temperature of 100 ± 5 ℃ for 6h. And then it shall be subjected to standard atmospheric conditions for 1h, after which its measurement shall be made. |
沒有外形變形，上蓋脫落等異常，滿足電氣性能。 Without deformation of case or excessive looseness of caps. Electrical characteristics shall be satisfied. |
|
2 |
低溫 Cold |
在-20±3℃環境保持500小時后，常溫常濕條件下放置1小時后進行測量。 The fuse shall be stored at a temperature of -20±3℃ for 500h. And then it shall be subjected to standard atmospheric conditions for 1h, after which its measurement shall be made.
|
|
|
3 |
濕熱 Damp heat |
在40±2℃、相対濕度90～95％RH環境保持250小時后，常溫常濕條件下放置1小時后進行測量。 The fuse shall be stored at a temperature of 40±2℃with relative humidity of 90 to 95%RH for 250h. And then it shall be subjected to standard atmospheric conditions for 1h, after which its measurement shall be made. |
|
|
4 |
耐久測試 Endurance test |
給產品通電100A電流5ms，斷開995ms為一個周期，一起循環一萬個周期。 100A be carried for a period of 5ms. The current is there switched off for a period of 995ms.this cycle is repeated 10,000 times. |
外形無明顯變形、破損，保險絲組件沒有熔斷。 Without damage such as deformation or disconnection of fuse element. |
